Cole CH1 Picklefork Hydro Drag Boat

Description

Gorgeous 1978 Cole CH-1 vintage drag hydro with trailer and engine turnkey, ready to run. Hull is 18' 6" in length.

Background

Originally built by the late Jim Cole for the late drag boat racer Sunny Jones, in 1978. He later sold it (sans engine) to an individual in 1981-82 from whom I bought it in '83 and who informed me that it once belonged to Sunny. I spoke with Sunny about it before my purchase and he said it was a good boat and he had intended to race it in the Blown Alcohol Hydro class but (for reasons I can't recall) he scrapped the idea and decided to pursue racing Cole flats instead. So I bought it and installed the (freshly-built) Ford engine. I used it as a recreational lake boat for only about 3 seasons, then raced it in one race and had to move to Indiana. After moving it from Reno, Nevada, I had it out to the lake 3-4 times. It has been in storage virtually from that point on and it is (sadly) now time for someone else to have the opportunity to enjoy it as I have.

Performance (with current engine)

At 4300' elevation in 1984, it ran low-11's in the mid-90 mph range on a timed, quarter-mile drag course with 91 octane pump gas. It's now tuned for sea level (~700'), but ET's at this elevation are unknown. This boat is a bit heavier and more solidly constructed than those designed for class racing. As such, it makes a durable lake or bracket racing boat. The hull is designed to handle lots of horsepower without stress cracking.

About the PICTURES

The paint on this boat is gorgeous and highly reflective. This made it difficult to photograph. Unless the lighting is just right, reflections may look like scratches. Also, unless the lighting angle is just right, the paint may look dull in some shots. There may be some minor dulling in a few areas, but that can be (and has been on occasion) rubbed out. If you're concerned about what appears to be a paint defect, try viewing the same area from different photo angles if supplied. Please contact me about specific concerns. I have added captions to some pictures to highlight where there is paint damage, in the spirit of full disclosure.

Chrome

All external rudder and bracket mountings on rear of boat were recently re-chromed. They are a bit dirty in the picture but NOT pitted, except for cavitation plate bracket issue listed below. Also, the white flecks on the backs of the seats are dust from a towel, not pitting. The photos were taken in the winter, so thorough cleaning prior to shooting was not possible.

Disclosure

As you can see from the detail included with this auction, our intent is to disclose any known defects or issues. However it is possible that we may have missed some. So, if you have any particular concerns, study the pictures then ask for details in order to ensure your satisfaction.

Hull Description

• Model:

  1978 Cole CH-1 Drag Hydro with outboard steering

• Hull:

  Premium, sealed mahogany floor and stringers, built to

  withstand the stress of racing a supercharged alcohol motor (at the

  time of hull construction, in 1978)

• Steering:

  Deaver outboard with removable rudder, all fully chromed where possible

• Seating:

  Two seats, steering offset to left

• Fuel

  System: left and right-side, spun aluminum tanks, approximately 10

  gallons each; one Holley "blue" GPH110 electric fuel pump

  with external regulator; dual Fram HPG1 fuel filters (one on each

  tank), Russell high volume fuel log on carburetors

• Gauges:

  Jones mechanical tachometer driven from v-drive, Stewart-Warner oil

  pressure, voltmeter and water temperature gauges with electrical

  sending units where applicable

• V-Drive:

  Casale 10 degree (gear ratio unknown but optimized for current engine and prop); Casale service

  documentation provided

• Propellers: Two (2) props supplied. Precision Propeller 3-blade cleaver (currently

  used) and a 2-blade std. non-cleaver style (mfr. unknown)

• Mounting Hardware: Trimetric anodized in most areas
• Additional

  tools supplied: V-drive bearing puller, propeller puller, Casale v-drive documentation

• Accessories:

  Tether ignition kill switch, high volume electric bilge pump, short

  ~36" oar with retaining clip on stringer, water engine coolant

  intake and exhaust lines; battery

  mounting hardware, 12v battery, Lexan splash guard, leatherette bra

  for sponson towing protection, anchor, hold-down straps

Trailer Description

Custom Made tandem wheel trailer.

• Has vintage Crager "SS" look-alike wheels with good chrome

• Chrome fenders and Black Imron-painted frame

• "Bearing Buddies" on spindles for ease of lubrication; Protective spindle caps are included

No trailer brakes but I have never needed them. This setup tows flawlessly with any truck or SUV that can legitimately handle a 2 receiver hitch and associated load. Trailer light connector wiring diagram included

Engine

Ford 429 V-8 engine; balanced and blueprinted 1968 short block, bored .030 over

• Crankshaft:

  Stock (base) 429 with chamfered oil holes (balanced)

• Connecting

  Rods: Rare, genuine Boss 429 #C9AE-B (C9AZ-6200-B)

• Pistons:

  TRW forged pistons, 030" over, with effective compression ratio

  of 10.8:1 or higher

• Oil

  System: Heavy duty distributor drive shaft; TRW pump, clearanced and

  lapped; Milodon 9qt. front sump oil pan; Moroso vac-u-pan system.

• Heads:

  Original 1968 429 ported and fitted with 2.19" TRW intakes and

  1.75" exhaust valves, bronze guides and Teflon seals. Crane

  1.71:1 roller rockers. Crane pushrods custom-length fitted for

  proper rocker arm geometry.

• Camshaft:

  Schneider solid-lifter custom camshaft grind (card included).

• Timing

  Set: Cloyes True-Roller Timing Chain.

• Ignition:

  Mallory Unilite distributor with bronze drive gear. MSD 6A

  ignition amplifier. Mallory coil, Mallory 7mm stainless core 7mm silicone spark plug wires

• Intake

  and Carburetors: Weiand Dual-Quad Tunnel Ram manifold with 2- Holley

  R-4778 700cfm double-pump carburetors with velocity stacks, screens

  and covers

• Cooling:

  Magnaflow marine water pump, Nicson front timing cover

• Headers:

  Bassett dry stack (black) with covers

• Electrical:

  Battery and charging system (alternator & regulator) included

• Other:

  Misc. documentation provided for Casale v-drive, ignition system and

  other parts, along with original Cole brochure

Known issues:

• Shallow

  gouge on left-rear corner (see photo)

• Shallow

  scrape on right sponson edge

• Smooth

  paint abrasion on left and right side rear, no damage to glass

• Light

  stains in paint from fuel tank overflow near filler neck

• Water-repellant coating under hull is showing some wear
• Cavitation

  plate bracket has some peeling chrome

• Mis.

  small nicks in paint in various places but are so small they don't

  show in pictures

• Some

  gouges in paint on rear trailer deck from the scag on the sponson

• Dent

  in trailer-boat chrome center hold-down bracket

• Dimple

  in right, trailer fender, toward inside

• Sponson

  bra is showing signs of wear with "fuzz" coming off, along

  with some tears

• If there is any weird coloration, it is probably

  glare or reflection(check pictures closely)

DELIVERY: Buyer will be responsible for the additional costs incurred to move or to arrange local pick-up (Indianapolis, IN).