Home » JC Boles » JC Boles

JC Boles

Price: 
$3,999
Boat location: 
San Tan Valley, Arizona, United States
Ships to: 
United States
Year: 
2008
Make: 
JC Boles
Type: 
Pontoon
Hull Material: 
Aluminum
Trailer: 
Included
Engine Type: 
Electric
Primary Fuel Type: 
Electric
For Sale By: 
Private Seller
Hull ID Number: 
LYQ12A07B808
Length: 
14.0 feet
Beam: 
8.0 feet
Raiting: 
Average: 5 (7 votes)
JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
  • JC Boles 2008
Condition: 
Used
Advertisements: 
Seller Notes: 
Boat and trailer are in good used condition. 2 new trolling motor batteries.
Description: 

I have a used 2008 JC Boles 14' long by 8' wide electric pontoon boat with trailer. This boat is ideal for a family that lives in a lake or canal subdivision that has electric motor restrictions. I have just installed 2 new group 27 deep cycle batteries. Boat comes with a built in 2 battery charger. There is also a bimini top for the sun. There is under seat storage in the two back lounges and the boat has 3 additional seats. Boat functions as is and will service your needs. The boat is 10 years old so please do not expect it to look like new.I have the registration for the boat and title for the trailer. Local pickup only and if you want it shipped you will be responsible for all aspects of shipping. Boat is for sale locally.

Questions

Lorraine Darnall - 29/07 9:19PM

Is your pontoon boat still for sale?
If so how many people can it hold?
Do you know it's NMMA rating for hp of a gas motor?

Debbie - 25/09 12:44PM

I just bought a 2010 JC Boles pontoon boat from a woman who knew nothing about it. Would you be able to tell me something about the pontoons? What’s in the inside the pontoons ( chambers, flotation material, ...) and do they need sealant outside on the seams? There’s a blue tube near the top of each pontoon that is open. Not sure what those are for. I tried to call the company and number is disconnected. Thanks for any info you can give.

Tom Soper - 25/12 1:57AM

I had to replace the flotation parts of the pontoons due to an infestation of ants. The flotation was simply 2" while insulation board you'd buy at Lowes or Home Depot. The insulation had really deteriorated into a lot of tiny pieces of white foam. The top of the pontoon you describe is designed to keep all the flotation "stuff" contained and inside the pontoon, allowing flotation even if it's deteriorated into pieces.
I replaced the white foam boards with blue or pink closed cell boards. It took mostly 2" boards, with a 3" board on top. There should be a small bilge pump at the rear of each pontoon, which pumps water into the very front, angled, parts of the pontoons. Those front parts are not sealed and have no flotation boards. I replaced each of the bilge pumps, using clear plastic (and flexible) tubing to route the pumped water to the front.
You must tie your motor to the boat. The "transom" broke on mine & the motor dropped 25 to the end of its rope. I was able to lift it onto the boat and get it serviced so it still works. I highly recommend getting a welder to build you a more substantial "transom"

Tom Soper - 25/12 2:11AM

Two other things: 1) There's not a lot of clearance between the top of the tire and the bottom of the pontoon. If you plan on carrying much weight in the boat while towing, you might want to replace the 2x4s with 2x6s.I'd suggest heavy, pressure treated wood, or the trailer will tend to float without the boat on it. Replacement is easily done after launching the boat. 2) The boat will re-load onto the trailer much easier if you connect the 2 guiding 2x4s on the sides, at the top, with a 2x4 or 2x6, carpeted

Add new question to the seller